Troubleshooting your Dodge Intrepid can save you alot of money in mechanic fees. It's pretty easy to get the codes from your Intrepid.
Turn the ignition key ON/OFF.ON/OFF/ON for about 5 seconds. Do not start the car.
After you do this watch your check engine light. You will need to count the flashes.
Flash-Flash-Flash-Flash [Pause] Flash-Flash = 42
There will be a longer pause for a separate error code.
Below is the list of all the error codes for the first gen Dodge Intrepid.
________________________________________________
11 - Timing belt skipped 1 tooth or more from initial learned value, Intermittent loss of either camshaft or crankshaft position sensor, No crank reference signal detected during engine cranking
12 - Direct battery input to PCM was disconnected within the last 50 key-on cycles
13 - No change in MAP from start to run
14 - MAP sensor voltage too low
15 - No vehicle speed sensor signal
17 - Closed loop temp not reached or engine cold too long
21 - 02s sensor problem (oxygen sensor), upstream or down stream
22 - Engine coolant temp sensor out of range
23 - Intake air temp sensor out of range
24 - Throttle Position sensor out of range
25 - Idle air control motor circuits, target idle not reached (+/- 200),vacuum leak found
27 - Injector control circuit
31 - Evap purge flow monitor failure or evap solenoid circuit
32 - EGR system failure
33 - A/C clutch relay circuit
34 - Speed control Solenoid circuits
35 - Rad Fan control relay circuit
37 - Torque converter clutch solenoid CKT or park/neutral switch failure
41 - Generator field not switching properly
42 - Fuel pump relay control ckt, Auto shutdown relay control ckt, No ASD relay output voltage at PCM, Fuel level sending unit volts out of range, Fuel level unit No change over miles
43 - Multiple/ single cylinder misfire
44 - Battery temp sensor volts out of range
46 - Charging system voltage too low
51 - Fuel system lean
52 - Fuel system rich
53 - Internal control failure
54 - No Cam signal at PCM
55 - End of error messages (If you get this only, no errors were found)
62 - PCM failure SRI mile not stored
63 - PCM Failure EEPROM write denied
64 - Catalytic Converter Efficiency Failure
65 - Power steering switch failure
12 - Direct battery input to PCM was disconnected within the last 50 key-on cycles
13 - No change in MAP from start to run
14 - MAP sensor voltage too low
15 - No vehicle speed sensor signal
17 - Closed loop temp not reached or engine cold too long
21 - 02s sensor problem (oxygen sensor), upstream or down stream
22 - Engine coolant temp sensor out of range
23 - Intake air temp sensor out of range
24 - Throttle Position sensor out of range
25 - Idle air control motor circuits, target idle not reached (+/- 200),vacuum leak found
27 - Injector control circuit
31 - Evap purge flow monitor failure or evap solenoid circuit
32 - EGR system failure
33 - A/C clutch relay circuit
34 - Speed control Solenoid circuits
35 - Rad Fan control relay circuit
37 - Torque converter clutch solenoid CKT or park/neutral switch failure
41 - Generator field not switching properly
42 - Fuel pump relay control ckt, Auto shutdown relay control ckt, No ASD relay output voltage at PCM, Fuel level sending unit volts out of range, Fuel level unit No change over miles
43 - Multiple/ single cylinder misfire
44 - Battery temp sensor volts out of range
46 - Charging system voltage too low
51 - Fuel system lean
52 - Fuel system rich
53 - Internal control failure
54 - No Cam signal at PCM
55 - End of error messages (If you get this only, no errors were found)
62 - PCM failure SRI mile not stored
63 - PCM Failure EEPROM write denied
64 - Catalytic Converter Efficiency Failure
65 - Power steering switch failure
Hi. I’m the blog owner. I’m here to help you the best I can with useful posts to help you fix your mopar.
0 comments:
Post a Comment